Aluminum Body Butterfly Valve is a product in the valves family for fluid conduction in aluminum. Available made to order, quoted via WhatsApp. Supplied on request.
| Family | Valves |
| Material | Aluminio |
| Connection | Other |
| Sales unit | Se vende por Unidades (Unid.) |
| Availability | Made to order |
The aluminum body butterfly valve is a quarter-turn valve for air and bulk solids (cement, powders, tanker and silo discharge). The aluminum body (density 2.70 g/cm³) weighs 62 % less than an equivalent cast iron one (7.15 g/cm³), which suits it for mounting on mobile equipment. Made to order.
| Feature | Specification |
|---|---|
| Type standards | API Std 609 (9th ed., 2021) and MSS SP-67-2022 — wafer, lug and flanged butterfly valves |
| Body | Aluminum, density 2.70 g/cm³ — 62 % lighter than cast iron (7.15 g/cm³) at equal geometry |
| Configuration | Wafer or lug per reference — confirm when quoting |
| Disc and seat | Lot materials confirmed when quoting; validated against the conveyed solid or gas |
| Automation | Actuator interface per ISO 5211:2026 where the reference includes it — confirm platform when quoting |
| Typical service | Low-pressure air and bulk solids: cement, lime, powders, pneumatic discharge of tankers and silos |
| Working pressure | Not published for the lot — confirm when quoting |
| Availability | Made to order, per unit |
Before using these data in engineering decisions — design, installation or systems with mechanical risk of pressure, rupture, fatigue, impact or water hammer — you must read the Technical notice and limitation of liability at the end of this page.
We dispatch aluminum body butterfly valves to Bogotá, Medellín, Cali, Barranquilla and all of Colombia. Request a quote via WhatsApp with size, flange pattern, conveyed material and quantity to confirm made-to-order lead time and price.
For weight: aluminum has a density of 2.70 g/cm³ versus 7.15 g/cm³ for cast iron, 62 % less at equal geometry. On tankers, mobile silos and pneumatic discharge lines that reduction eases mounting on the equipment and lowers the structural load.
General-purpose wafer and lug butterfly valves are covered by API Std 609 (9th edition, 2021) and MSS SP-67-2022, which define dimensions, design, testing and marking. The lot reference conformity is confirmed when quoting.
Yes: when the reference carries the mounting interface per ISO 5211:2026, a pneumatic or electric quarter-turn actuator can be fitted; the platform (F05, F07, etc.) and required torque must be checked against the chosen actuator.
It is a made-to-order reference: the price depends on size, wafer or lug configuration, disc and seat materials and quantity. TECTUL quotes via WhatsApp with the conveyed material and actual conditions.
Before using these data in engineering decisions — design, installation or systems with mechanical risk of pressure, rupture, fatigue, impact or water hammer — you must read the Technical notice and limitation of liability at the end of this page.
Polypropylene Fusion Ball Valve Cold Fluid
Polypropylene Yee Check Valve
Ball Valve with Polypropylene Fusion Male Thread Adapter / Brass
Ball Valve with Polypropylene Fusion / Brass Adapter
Ball Valve with Female Thread Adapter Polypropylene FusionUpdated: July 22, 2026
The dimensions, thicknesses, pressures, temperatures and other characteristics stated in this data sheet are theoretical nominal reference values, compiled from publicly available technical sources: international standards (ASME, ASTM, API, MSS, ISO and NTC, depending on the product) and published engineering literature. They are average approximations intended to guide selection, not a certificate of conformity for any given lot.
Actual values may vary due to conditions inherent to the manufacturing process — dimensional and wall-thickness tolerances (in pipe, typically ±12.5%), surface finish and residual stresses from forming or welding — and to factors inherent to the raw material — chemical composition variations within the ranges allowed by the standard, inclusions or heat-to-heat differences. They may also be affected by in-service events not foreseeable at design time: water hammer, vibration, thermal and mechanical fatigue, corrosion and operating overpressures, which can cause the element to fail before its estimated service life.
To know the certified behavior of a specific lot, TECTUL supplies upon request the manufacturer's mill test certificate (MTC) issued per the product standard; for critical applications, laboratory testing of the lot can also be arranged. In the absence of such certification, the data provided here must not be used as the sole criterion in critical or safety applications, or wherever the integrity of the line may compromise the lives of people or property; in such cases, consult our technical team first.
